aspen模拟氨合成回路出现问题，麻烦告诉我下什么地方出错了

douhaifeng12 · 发表于 1970-1-1 08:00:00

本帖最后由 douhaifeng12 于 2016-5-16 15:15 编辑

麻烦大家帮忙看下吧，万分感激

->Processing input specifications ...

   THE PAIR PARAMETERS FOR ELECNRTL OPTION SET HAS BEEN RETRIEVED FROM
   DATABANK ENRTL-RK.

   INFORMATION
   PURE COMPONENT PARAMETERS FOR SOME COMPONENTS ARE RETRIEVED FROM
   DATABANK.  THESE PARAMETERS ARE USED WITH THE ELECNRTL OPTION SET
   UNLESS YOU ENTER YOUR OWN PARAMETERS IN PROP-DATA PARAGRAPHS.
   PARAMETER VLBROC RETRIEVED FOR COMPONENT NH3

   PARAMETER THRSWT(ELEMENT/3) RETRIEVED FOR COMPONENT H2O

   PARAMETER PLXANT RETRIEVED FOR COMPONENT H2O

  * WARNING WHILE CHECKING INPUT SPECIFICATIONS
   INCONSISTENT PROPERTIES DETECTED FOR STREAM "5"
   FROM BLOCK: "E3"  PROPERTIES: PR-BM
      TO BLOCK: "E4"  PROPERTIES: PENG-ROB

  * WARNING WHILE CHECKING INPUT SPECIFICATIONS
   INCONSISTENT PROPERTIES DETECTED FOR STREAM "1"
   FROM BLOCK: "E3"  PROPERTIES: PENG-ROB
      TO BLOCK: "R"  PROPERTIES: PR-BM

  Flowsheet Analysis :

Block $OLVER01 (Method: WEGSTEIN) has been defined to converge
      streams: 1-1    4

COMPUTATION ORDER FOR THE FLOWSHEET:
E7
$OLVER01 E3 E4 E5 R E1 E2
(RETURN $OLVER01)
S1 F M E6 S

->Calculations begin ...

Block: E7    Model: HEATER

> Beginning Convergence Loop $OLVER01 Method: WEGSTEIN

Block: E3    Model: HEATX
  * WARNING
   AT LEAST ONE FEED HAS ZERO FLOW
   BLOCK BYPASSED

Block: E4    Model: HEATX
  * WARNING
   AT LEAST ONE FEED HAS ZERO FLOW
   BLOCK BYPASSED

Block: E5    Model: HEATX
  * WARNING
   AT LEAST ONE FEED HAS ZERO FLOW
   BLOCK BYPASSED

Block: R       Model: RSTOIC
  * WARNING
   TOTAL FLOW IS ZERO

Block: E1    Model: HEATX
  * WARNING
   AT LEAST ONE FEED HAS ZERO FLOW
   BLOCK BYPASSED

Block: E2    Model: HEATX
  * WARNING
   AT LEAST ONE FEED HAS ZERO FLOW
   BLOCK BYPASSED

> Loop $OLVER01 Method: WEGSTEIN    Iteration 1
  * WARNING
   THE VALUES FOR SOME VARIABLES ARE MISSING.
   THIS MAY BE CAUSED BY A ZERO-FLOW STREAM.
   THE PREVIOUS VALUES OF THE VARIABLES WILL BE USED.
   THE MISSING VARIABLES ARE:
   "15" THRU "16"

6 vars not converged, Max Err/Tol 0.10000E+07

Block: E3    Model: HEATX
  * WARNING
   AT LEAST ONE FEED HAS ZERO FLOW
   BLOCK BYPASSED

Block: E4    Model: HEATX
  * WARNING
   AT LEAST ONE FEED HAS ZERO FLOW
   BLOCK BYPASSED

Block: E5    Model: HEATX
  * WARNING
   AT LEAST ONE FEED HAS ZERO FLOW
   BLOCK BYPASSED

Block: R       Model: RSTOIC

Block: E1    Model: HEATX
  **  ERROR
   INVALID HOT STREAM TEMPERATURE SPECIFICATION
   T-SPEC =  4.9915000D+02 IS MORE THAN THIN =  4.4307061D+02

Block: E2    Model: HEATX

> Loop $OLVER01 Method: WEGSTEIN    Iteration 2
8 vars not converged, Max Err/Tol 0.10000E+05

Block: E3    Model: HEATX

Block: E4    Model: HEATX

Block: E5    Model: HEATX

Block: R       Model: RSTOIC

Block: E1    Model: HEATX

Block: E2    Model: HEATX

> Loop $OLVER01 Method: WEGSTEIN    Iteration 3
1 vars not converged, Max Err/Tol 0.98878E+03

Block: E3    Model: HEATX

Block: E4    Model: HEATX

Block: E5    Model: HEATX

Block: R       Model: RSTOIC

Block: E1    Model: HEATX

Block: E2    Model: HEATX

> Loop $OLVER01 Method: WEGSTEIN    Iteration 4
# Converged             Max Err/Tol 0.00000E+00

Block: S1    Model: FLASH2

Block: F       Model: FSPLIT

Block: M       Model: MIXER

Block: E6    Model: HEATER

Block: S       Model: FLASH2

->Generating block results ...

Block: E4    Model: HEATX

Block: E5    Model: HEATX

Block: E3    Model: HEATX

Block: E2    Model: HEATX

Block: E1    Model: HEATX

->Simulation calculations completed ...

  ***  No Warnings were issued during Input Translation ***

            ***  Summary of Simulation Errors  ***

               Physical
               Property       System       Simulation
  Terminal Errors    0             0             0
Severe Errors    0             0             0
         Errors    0             0             1
      Warnings    0             0             11

丙零城下 · 发表于 1970-1-1 08:00:00

我的也是如此，求大神解救

aspen模拟氨合成回路出现问题，麻烦告诉我下什么地方出错了

相关帖子